General Settings

Date

Date Setting:

1. Press the controller button (6) briefly to enter the Date  submenu. The date is displayed in dd/mm/yyyy format.
2. Rotate the controller ring (6) to select the desired year, month and date. Press the controller button (6) briefly to switch between digits.
3. Press and hold the controller button (6) to save your selected date and exit from the submenu.

Time

Time Setting:

1. Press the controller button (6) briefly to enter the Time  submenu.
2. Rotate the controller ring (6) to select the time format - 24 or AM/PM.
3. Press the controller button (6) to proceed to the hour setting.
4. Rotate the controller ring (6) to select the hour value.
5. Press the controller button (6) to proceed to the minute setting.
6. Rotate the controller ring (6) to select the minutes value.
7. Press and hold the controller button (6) to save your selected time and exit from the submenu.

Units of Measure

Units of measurement selection:

1. Press the controller button (6) briefly to enter the Units of Measure submenu.
2. Rotate the controller ring (6) to select the unit of measurement - meters or yards, press the controller button (6).
3. Return to submenu will happen automatically.

Video Compression

When set to ON, standard video compression is applied so the video file size is reduced.

When set to OFF, minimal video compression is applied. In this case, the record quality is higher, but its size increases significantly.

Warning! Larger video file size results in reduced video recording time. This may lead to longer download times for video files through the Stream Vision 2 app.

Enable/disable video compression:

1. Rotate the controller ring (6) to select the Video Compression  menu item.
2. To turn on video compression, briefly press the controller button (6).
3. To turn off video compression, briefly press the controller button (6). 

Auto Shutdown Options

1. Rotate the controller ring (6) to select Auto Shutdown Options .
2. Press the controller button (6) to enter the submenu.

If device inactive for 30 min

When this feature is enabled, the device automatically turns off after 30 minutes of inactivity Display off mode.

1. Rotate the controller ring (6) to select If device inactive for 30 min .
2. Press controller ring (6) to select On for turning on the function or Off for turning it off.

If in idle position

1. Rotate the controller ring (6) to select If in idle position .
2. Press the controller button (6) to enter the submenu.
3. Rotate the controller ring (6) to select the time period (1 min, 3 min, 5 min) upon expiry of which the riflescope will automatically shut down, or select Switch off if you wish to deactivate Auto Shutdown.
4. Confirm your selection with a short press of the controller button (6).

Note: If the automatic shutdown function is activated, the status bar shows an icon ​and shutdown time period as 1/3/5 min.

Side Incline

This item allows you to activate or deactivate the “sector” arrows on the sides of the display. These arrows show the direction in which your rifle scope should be rotated to eliminate incline.

There are three modes of incline:

• 5°-10° – one sector arrow;
• 10°-20° - two sector arrow;
• > 20° - three sector arrow.

A side incline of less than 5° is not displayed.

1. Rotate the controller ring (6) to select Side Incline .
2. Press controller ring (6) to select On for turning on the incline indication or Off for turning it off.

Viewing Channel Activation

This submenu allows you to turn off one of the image channels (thermal imaging or digital) if it is not used.

Turning off the image channel will save battery power.

An icon with a disabled channel will be displayed in the status bar: or .

Turn on/off the image channel:

1. Rotate the controller ring (6) to select the Viewing Channel Activation menu item.
2. Press the controller button (6) briefly to enter the submenu.
3. Rotate the controller ring (6) to select the image mode: thermal imaging or digital.
4. Confirm your selection with a short press of the controller button (6).
5. Turn on/off the image channel by briefly pressing the controller button (6).

Default Settings

1. Press the controller button (6) briefly to enter the Default Settings submenu.
2. Rotate the controller ring (6) to select “Yes” to restore default settings or “No” to cancel the action.
3. Confirm your selection with a short press of the controller button (6).

• If “Yes” is selected, display will show “Do you want to restore default settings?” with “Yes” and “No” dialogue options. Select “Yes” to restore default settings.

• If “No” option is selected: the action will be aborted and you will return to the submenu.

The following settings will be returned to their defaults:

• Video Recorder Mode – Video
• Amplification Level – Normal
• Smoothing Filter – Off
• User Mode - Off
• Calibration Mode – automatic
• Interface Language – English
• Wi-Fi – Off (unique password)
• Magnification – initial value
• PiP – Off
• Color Mode – White hot
• Units of Measurement – metric
• Side Incline – On
• Zeroing Profile – A
• Reticle selection from the riflescope’s memory – 1
• Video Compression – Off
• Wi-Fi Band – 2.4 GHz
• Viewing Channel Activation – both channels are on
• Ballistic calculator – On
• Ballistic calculator units – MOA
• Display dimming – Off
• Auto shutdown if device inactive for 30 min – On

Attention! After restoring default settings, the date, time and user pixel map as well as the zeroing profiles data entered by the user are saved.